AP1682 LED DRIVER DOWNLOAD

The compensation circuit should meet Because VPK pin senses the peak value of sine waveforms, a low pass filter is required to get the average value of sine waveform voltage. Begin from the central column of the Bobbin. Since of PFC operation and the special PFM control technology, the circuit operation parameter of Flyback converter is little different with the traditional off-line Flyback converter. At start-up phase, after VCC voltage reaches turn on threshold, AP controls the power converter operating at the max frequency with DCM Boundary mode to provide more energy to output. The transformer design should be based on the worst case operation condition. Supply voltage of gate driver and control circuits of the IC. As shown in Figure 5 and Figure 6, comparing to the Flyback application, the Buck-Boost converter has only inductor instead of transformer, has not primary snubber circuit.

Uploader:	Yosho
Date Added:	1 April 2007
File Size:	33.59 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	28481
Price:	Free* [*Free Regsitration Required]

When open load condition or load disconnecting happens, the output voltage rises to the maximum value and the FB pin voltage reaches 4V. As shown in Figure 5 and Figure 6, comparing to the Flyback application, the Buck-Boost converter ledd only inductor instead of transformer, has not primary snubber circuit.

Begin from the central column of the Bobbin. Finish on Pin 6. The compensation circuit aap1682 meet Because VPK pin senses the peak value of sine waveforms, a low pass filter is required to get the average value of sine waveform voltage. BCD will release the AP design sheet tools for both Flyback and Buck-Boost application to meet the all types of application requirements. Use Voltage Divider Rule to find 1.

(PDF) AP1682 Datasheet download

FB Function Region Diagram 4. The AP achieves excellent regulation and high efficiency, yet meets the requirement of IEC harmonic standard.

Transformer Winding Construction Diagram Apr. The rectified input voltage peak value sensing pin.

Design Guideline and Application Notes of AP System Solution

Since of PFC operation and the special PFM control technology, the circuit operation parameter of Flyback converter is little different with the traditional off-line Flyback converter. Therefore the VCC voltage which comes from aux winding coupling with transformer winding also needs the wider operating voltage range.

There lee always output capacitors to filter the ripple in Flyback topology, so the output voltage ripple lrd on the total output capacitance. Insulation 1 Layer of insulation tape [7], 0.

Data sheet, Mechanical dimensions soic-8 unit: mm(inch) | Diodes AP User Manual | Page 10 / 11

Review of LR circuits. Certainly, the efficiency and BOM cost are also the important factors for components selection.

Wind another 39 Primary winding turns on the next layer from right to left. Supply voltage of gate lev and control circuits of the IC. The most components of Flyback and Buck-Boost have same Apr. It is assumed that the secondary diode forward voltage drop Vd is about 0.

Data sheet, Mechanical dimensions soic-8 unit: mm(inch) – Diodes AP1682 User Manual

So the AP also can be used in non-isolated Buck-Boost application. The pin is detecting the instantaneous rectified sine waveform of input voltage 3 VPK The rectified input voltage peak value sensing pin.

Current return for gate driver and control circuits of the IC. From above output current equation it is concluded that the output current zp1682 the double line frequency AC components, which results in the double line frequency output voltage and output current ripple.

W3 Secondary Winding Start at white terminal. This pin ap682 the feedback voltage from the auxiliary winding. Operation Parameter Components Selection Design design method. Current return for gate driver and control circuits of the IC. This will lead to AP latch working mode. EF16, PC40 or equivalent 2 Bobbin: The AP start-up voltage threshold is The design specification is 8.

At start-up phase, after VCC voltage reaches turn on threshold, AP controls the power converter operating at the max frequency with DCM Boundary mode to provide more energy to output. Electrical Diagram Figure 7.